Unitech MS920 Manual do Utilizador

Wireless Pocket 2D Imager Scanner- MS920 -User's ManualVersion 2.0© 2014 unitech Electronics Co., Ltd. All rights reserved. unitech is a register

- 4 -SpecicationsLight sourceIllumination: Highly visible white LEDAiming : 617 nm red LEDScan rate240 scans/secSensorLinear CMOS sensorResolution1D

- 94 -5000Disable/enable all good read signals- This setting can be used to disable all good read signals: Beep, LED and vibrate.DisableEnable (*)Err

- 95 -Multicode beeps- By default the scanner does not beep when reading several bar codes when using the Multicode function (see Symbologies). Use t

- 96 -Data Transmission SettingsChapter 5- Modify data transmission settings to optimize performance.ISCP- MS920 Scanner Control Protocol parameters.I

- 97 -- Precedes barcode data with "[BCD]" indicator.BCDBCDEX (*)- "Packet" data format must be activated to enable BCDEX transmi

- 98 -- Error (if any)- Type of ISCP bar code (setup, status, etc.)- GID- FID- Parameter- For information on the event frame received by the host see

- 99 -Unsuccessful decoding- This event is sent whenever a decode session is deactivated (trigger released) and no decode has taken place.Disable (*)

- 100 -EnableTrigger pulledDisable(*)EnableTrigger releasedDisable(*)EnableWake-upDisable(*)EnableStructured appendDisable(*)

- 101 -EnableSymbology identier [symbology id] [data] Not transmitted(*)AIM format [AIM symbology id] [data]- Activates for all symbologies the 3-

- 102 -Code Mark[preamble] [code mark symbology id] [data] [postamble]- Activates code mark symbology identier transmission for all symbologies.NO

- 103 -Inter-Character / message delay- Avoids dropping characters if transmitting decoded data too fast for the host system.Inter-Character delay-

- 5 -Pairing With PC/Notebook For The First TimePC (HID mode)Following steps are based on Microsoft Windows 7.1. Use MS920 to scan barcode “HID”.2.

- 104 -Inter-message delay- Value is in milliseconds.0 (*)10305080100Data editing- IMPORTANT [[[[ The data editing function is only available with S

- 105 -- The order in which you dene the scenarios is important (the product compares incoming data with each scenario in turn and edits the data f

- 106 -Compose barcode length:Compose mask:Scenario 2Disable (*)EnableSelect barcode Type:Compose barcode length:Compose mask:Scenario 3Disable (*)

- 107 -EnableSelect barcode Type:Compose barcode length:Compose mask:Scenario 4Disable (*)EnableSelect barcode Type:Compose barcode length:

- 108 -Compose mask:Scenario 5Disable (*)EnableSelect barcode Type:Compose barcode length:Compose mask:Scenario 6Disable (*)Enable

- 109 -Select barcode Type:Compose barcode length:Compose mask:Scenario 7Disable (*)EnableSelect barcode Type:Compose barcode length:Compose mask:

- 110 -Get rmware version- Get version info.Get rmware versionGet decode version- Get decode version info.Get decode versionGet asub-system version

- 111 -Always enabledInhibit after 1 mn- Protects the product against unwanted conguration by bar code.- Conguration with bar codes only possible

- 112 -Worldwide SupportAppendix IUnitech’s professional support team is available to quickly answer questions or technical-related issues. Should an

- 6 -PC (SPP mode)Following steps are based on Microsoft Windows 7.1. Use MS920 t0 scan barcode “SPP”.2. Open Devices and Printers by clicking the S

- 7 -Switching Between HID and SPP ModeFrom SPP to HIDIf your MS920 is on SPP mode:1. Go to Devices and Printers under Control Panel, remove the MS9

- 8 -Factory Default Display F/W VersionBT Un-pair iOS KeypadInventory Space LeftCheck the memory size.Press the trigger once will display the ke

- 9 -Buffer ErasingInventory Mode Batch Mode1. Scan (Erase Inventory Buffer) . 1. Scan (Erase Batch Buffer)2. Scan (Erase) 2. Scan (Erase)For detail i

- 10 -Power SavingEnabled*(Good for scan with trigger)Disabled(Good for continuous scanning)BT Module Power Saving (Power off BT while no activities)1

- 11 -HID Keyborad Character Delay1 ms 5 ms10 ms 20 ms50 ms 100 ms

- 12 -HID Keyborad CaseAuto Trace To LowerTo UpperHID Keyborad Block Delay10 ms 50 ms100 ms 500 ms1 Sec. 3 Sec.

- 13 -HID Keyborad LanguagesUS English UK EnglishSwiss SwedishNorwegian ItalianGerman FrenchDanish Partial ALTJapanese SpanishALT Mode

- 14 -Enter BT Pairing CodeEnter AbortTo scan "//7" label to enter code input mode, to scan "digit" as prompted on host, to scan &

- 15 -- Symbology = bar code type or family (e.g. Code 39, UPC, EAN).- Activate the symbologies you need and modify the settings for your symbologie

- 16 -Symbology identierUser dened - User dened symbology identier.- See "Data transmission settings - symbology identier - UDSI" to

- 17 -A, B, C, DCheck digitcheck digit verication- AIM has a recommended check character for Codabar- Each Codabar data character (including Start/

- 18 -EnableBarcode length- Use the L1 as minimum length option if you know the minimum length of the codes in your application!!!- To optimize de

- 19 -Set lengths 1, 2 and 3- Set barcode length L1, L2 and L3 according to the barcode length mode used.Compose L1: Compose L2: Compose L3: Codabloc

- 20 -K1 (*)Compose: Please refer to SCM (Software Conguration Manager) in CDCode mark - See "Data transmission settings - symbology identier

- 21 -K1 (*)Compose: Please refer to SCM (Software Conguration Manager) in CDCode mark - See "Data transmission settings - symbology identier

- 22 -C1 (*)Compose: Please refer to SCM (Software Conguration Manager) in CDCode mark- See "Data transmission settings - symbology identier -

- 23 -Barcode Length- Use the L1 as minimum length option if you know the minimum length of the codes in your application!!!- To optimize decoding

Chapter 1Overview... 1Package Contents...

- 24 -Compose L2:Compose L3:Code 39- Alphanumeric symbology.- Letter case not dened - transmitted in upper case.- Format: standard 43 characters (

- 25 -Code mark- See "Data transmission settings - symbology identier - code mark" to activate or deactivate code mark transmission.- Us

- 26 -'$' only '$' only *'Check digitcheck digi vericationDisable (*)Modulo 43French CIPItalian CPIcheck digi transmission-

- 27 -EnableBarcode length- Use the L1 as minimum length option if you know the minimum length of the codes in your application!!!- To optimize de

- 28 -Set lengths 1, 2 and 3- Set barcode length L1, L2 and L3 according to the barcode length mode used.Compose L1:Compose L2:Compose L3:Reading ran

- 29 -High (*)MediumLowUnconventional Code 39- Used for decoding unconventional Code 39 such as:- very large inter-character- large ratio between n

- 30 -EnableCode 93/ Code 93i- Code 93 Alphanumeric full ASCII symbology - letter case dened.- Code 93i (encompasses and extends Code 93) Alphanu

- 31 -Code mark- See "Data transmission settings - symbology identier - code mark" to activate or deactivate code mark transmission.- Us

- 32 -L1 as min, L2 as maxSet lengths 1, 2 and 3- Set barcode length L1, L2 and L3 according to the barcode length mode used.Compose L1:Compose L2:Co

- 33 -GS1 - 128 disableSymbology identierUser dened- User dened symbology identier.- See "Data transmission settings - symbology identier

HID Keyborad Character Delay... 11HID Keyborad Block Delay...

- 34 -GS1 128D (*)Compose: Please refer to SCM (Software Conguration Manager) in CDGS1 - 128 identier- The ]C1 AIM identier for GS1-128 is automat

- 35 -L1 as Minimal length (*)L1, L2, L3 as xed lengthL1 as min, L2 as maxSet lengths 1, 2 and 3- Set barcode length L1, L2 and L3 according to the

- 36 -High (*)MediumLowReading range- Applies a special algorithm for long-distance reading (default setting).- Use the "normal" setting i

- 37 -Disable (*)TransmitDisable (*)Only transmit concatenated codesTransmit concatenated codes or single codesConcatenateDisable (*)EnableDataMatrix-

- 38 -DisableEnamle (*)Symbology identierUser dened- User dened symbology identier.- See "Data transmission settings - symbology identier

- 39 -Mirrored labels activation- When enabled mirrored labels can be read as well as normal labels.- When disabled only normal labels can be read.Dis

- 40 -EAN / UPC- Numerical symbology.UPC - A enable (*)UPC - A disableUPC - E enable (*)UPC - E disableEAN - 8 enable (*)EAN - 8 disableEAN - 13 enabl

- 41 -UPC - E1- Irregular UPC-E with number system equal to 1 (usually the rst printed character).- UPC-E must be active for UPC-E1 to be taken int

- 42 -EAN-8FF (*)Compose: Please refer to SCM (Software Conguration Manager) in CDEAN-13F (*)Compose: Please refer to SCM (Software Conguration Mana

- 43 -Compose: Please refer to SCM (Software Conguration Manager) in CDEAN-13F (*)Compose: Please refer to SCM (Software Conguration Manager) in CDA

Standard 2 of 5 ...71Telepen...

- 44 -security level10 (*)Compose: Please refer to SCM (Software Conguration Manager) in CDCheck digit transmission [leading character] [number syst

- 45 -EAN-13Enable (*)DisableUPC number system [leading character] [number system] [data] [check digit]UPC-AEnable (*)DisableUPC-EEnable (*)Disabl

- 46 -Re-encoding UPC-A, UPC-E, EAN-8[leading character] [number system] [data] [check digit]- Converts decoded data to other code formats.- Tran

- 47 -ISBN- International Standard Book Number- EAN-13 code, the rst 3 characters "978" or "979" (except for "9790")

- 48 -EnableReading range- Applies a special algorithm for long-distance reading (default setting).- Use the "normal" setting if distance

- 49 -Disable (*)Symbology identierUser dened- User dened symbology identier.- See "Data transmission settings - symbology identier - UDSI

- 50 -Disable (*)Symbology identierUser dened- User dened symbology identier.- See "Data transmission settings - symbology identier - UDSI

- 51 -EnableDisable (*)Symbology identierUser dened- User dened symbology identier.- See "Data transmission settings - symbology identier

- 52 -Interleaved 2 of 5- Numerical symbology.- For GTIN compatibility set barcode length to one xed length of 14 characters.Disable (*)EnableSymbo

- 53 -Compose: Please refer to SCM (Software Conguration Manager) in CDCheck digit- Especially recommended for variable length Interleaved 2 of 5 an

- 54 -- For GTIN compatibility set barcode length to one xed length of 14 characters- compose 1 or 2 or 3 xed lengths provides the best performanc

- 55 -Compose L3:Reading tolerance- Sets the tolerance level for reading hard to read bar codes.- High = most permissive (reads codes of variable qu

- 56 -Symbology identierUser dened- User dened symbology identier.- See "Data transmission settings - symbology identier - UDSI" to a

- 57 -ChinaPost- Specic start/stop characters (not transmitted) and checksum (transmitted).ChinaPostBarcode length- Use the L1 as minimum length

- 58 -Set length L1, L2 and L3- Set barcode length L1, L2 and L3 according to the barcode length mode used.Compose L1:Compose L2:Compose L3:MaxCode-

- 59 -D2 (*)Compose: Please refer to SCM (Software Conguration Manager) in CDCode mark- See "Data transmission settings - symbology identier -

- 60 -MicroPDF417- Two-dimensional symbology.- Alphanumeric full ASCII symbology - letter case dened.- It is highly recommended to select "st

- 61 -* (*)Compose: Please refer to SCM (Software Conguration Manager) in CDCode 128 emulation- When active and reading a MicroPDF code containing a

- 62 -- Use the default value or compose your custom symbology identier for this symbology (1 - 4 characters).B8 (*)Compose: Please refer to SCM (S

- 63 -DisableBarcode length- Use the L1 as minimum length option if you know the minimum length of the codes in your application!!!- To optimize d

- 1 -OverviewPackage ContentsPlease make sure the following contents are in the MS920 carton. If something is missing or damaged, please contact your

- 64 -Compose L1:Compose L2:Compose L3:PDF 417- Set barcode length L1, L2 and L3 according to the barcode length mode used.Enable (*)DisableSymbology

- 65 -Compose: Please refer to SCM (Software Conguration Manager) in CDCode mark- See "Data transmission settings - symbology identier - code

- 66 -Plessey Code- Numerical symbology.Disable (*)EnableSymbology identierUser dened- User dened symbology identier.- See "Data transmissi

- 67 -Check digit transmission [leading character] [number system] [data] [check digit]Disable (*)EnableUnconventional stopDisable (*)EnableBarcode

- 68 -- L3 = Codes at least the length specied by L1 and no longer than the maximum length specied by L2 are read (L3 is not used).L1 as Minimal le

- 69 -- Offers three levels of error detection.- Activating QR Code activates Model 2. Use the Model 1Control activation if you are using Model 1 (

- 70 -AutomaticMicroQR activation- Micro QR is a small QR code with only one pattern.Disable (*)EnableSymbology identierUser dened- User dened sy

- 71 -* (*)Compose: Please refer to SCM (Software Conguration Manager) in CDStructured appendDisable (*)EnableHeader transmissionDisable (*)EnableSta

- 72 -EnableSymbology identierUser dened- User dened symbology identier.- See "Data transmission settings - symbology identier - UDSI"

- 73 -Computer IdenticsCheck digitCheck digit vericationDisable (*)Modulo 10Check digit transmission- You can chose to transmit or not transmitted t

- 2 -Scanner DetailGetting StartedTo scan a barcode, make sure the aiming beam crosses every bar and space of the barcode.

- 74 -(L2 and L3 are not used).- L2 = Only codes that comply with the lengths specied by L1, L2, and L3 will be read.- L3 = Codes at least the leng

- 75 -Telepen- Alphanumeric full ASCII symbology - letter case dened.- Default format = ASCII. Disable (*)EnableSymbology identierUser dened- Us

- 76 -FormatASCII (*)NumericBarcode length- Use the L1 as minimum length option if you know the minimum length of the codes in your application!!!-

- 77 -L1 as min, L2 as maxSet length L1, L2 and L3- Set barcode length L1, L2 and L3 according to the barcode length mode used.Compose L1:Compose L2:

- 78 -- Settings that affect the way your product operates (trigger settings, ashing mode, data decoding security settings, beep characteristics, et

- 79 -AimScanning / TriggeringTriggering modesContinuous- At power up the lighting and decoding are on all the time. The trigger is not used.Continuo

- 80 -- When a bar code is detected, the lighting and decoding automatically turn on and stay on until another period of inactivity (timeout), after

- 81 -- The trigger can be used in Presentation mode - when you pull the trigger the scanner functions as if it were in Level mode.- Only available

- 82 -Trigger activation- Used to enable or disable hardware or emulated triggers.IMPORTANT: You cannot activate the trigger line if the hardware tri

- 83 -Enabled- Start read character default = STX- Stop read character default = ETX- This option is NOT compatible with ISCP.Enablestart character [S

- 3 -BATTERY CHARGING1. Flip up the rubber cover to expose the mini USB port on the scanner.2. Insert the mini USB connector into the port on the sc

- 84 -Turn off after good read- When active, the scan engine stops the reading session after a successful decoding.- Turn off after good read is onl

- 85 -- Pulse- Autostand- Toggle*NOTE*: In Toggle trigger mode, "one pull aim, one pull read" does not work as stated. Instead one pull turn

- 86 -- If you wait longer than the duration before the second pull, the cycle starts over with the aiming beam.500 (*)1200Compose (ms)Bad read messag

- 87 -Ignore stand detect- Enable ignore stand detect when you want to use Autostand triggering mode with and you are not using a detectable stand (c

- 88 -Data decoding security- Ensures correct transmission of data for difcult reading conditions and varying levels of barcode quality (poorly prin

- 89 -Timeout between identical consecutive codes (ms)- Prevents reading the same bar code more than once.- Value is milliseconds.Compose (ms):Timeo

- 90 -Tolerance- The tolerance level for center decoding allows you to aim the laser close to the bar code to be read rather than be positioned on th

- 91 -Beeps / LEDsNote (tone frequency)High (*)MediumLowPower-up beeps2 beeps = successful power-up3 long beeps = EEPROM integrity error (contact your

- 92 -1 beep (*)2 beepsNoneDuration6080 (*)200300Timing- IBM and OCIA cash registers: do not send this parameter online to the scan engine through RS

- 93 -During transmission (*)Before transmissionAfter transmissionGood read LED duration- "Read" LED green = "good read"- Settin